Standard Parts library to download

Hello.
I'm looking for standards part library( like fasteners) to download
besides using of SW ToolBox. Does anybody send me a links.
Thanks.

 

http://www.traceparts.com/en/online/index.asp

 

http://parts.web2cad.co.uk/PowerPartsOnWeb.ppow?GB

 

I'm copying a bunch of collected Palette Parts to my FTP host right this
minute. Been meaning to do it anyway. It'll be a little while yet
before they all get there, even at DSL speed, but you're welcome to
download whatever you find useful. Hopefully it won't be problematic --
yet to be seen because it's still uploading. My FTP host name is
"ftp.h2omarkdesign.com". UserID is "" and
password is "guestuser". If you have any problems set your FTP client
to enable passive file transfers. As far as I know you can't use
Netscape or IE for FTP with my site because the ampersand @ symbol seems
to violate those browsers' FTP syntax. You'll have to use something
like CuteFTP or WSFTP or similar software specifically designed to be
FTP clients.

Have fun downloading. There's a lot of crap there that I don't take
responsibility for. Those files were created by a several different
people besides myself and I haven't had time to go through all of them
and make them consistent. I DO believe that the parts represented are
dimensionally accurate.

Mark 'Sporky' Stapleton
Watermark Design, LLC
Charlotte, North Carolina, USA
www.h2omarkdesign.com

 

IE 6.0 does works. Don't know about Netscape.

Thanks for sharing your parts with everyone. I would share also if I had
the means to do it. If you have plenty of ftp space, I would be willing to
upload some of my stuff. Just let me know.

Is anyone sharing their material database yet?

 

Yeh, sure, I don't mind if you do. Just create a separate directory
(other than "/palette parts") up there. But please do wait until I'm
done uploading and until I have replied back here. I'm copying about
408 megabytes right now, plus I have all my Web pages and other stuff .
.. . and my limit is 800 megabytes. I'll let you know what the upper
limit of what you can upload will be. And I probably won't be able to
leave all this stuff up there indefinitely in an unprotected
environment. People are apt to upload stuff while I'm not looking that
I REALLY don't want up there.

IN FACT, after tomorrow morning (6/26, USA Eastern Standard Time), if
someone wants the files they can email me for a UserID and password. A
valid email address for me is at bottom on my main Web page (below).

Mark 'Sporky' Stapleton
Charlotte, NC
www.h2omarkdesign.com

 

ACK, getting crowded up there and still transferring files. 77% full
and climbing. Do not -- repeat, do not -- upload any files.

I'll allow this much stuff to remain on the FTP host all this weekend
and Monday, if anyone wants to download it. Come Monday afternoon it
comes off.

There's a lot of stuff here, people. A partial list by category:

8020 aluminum extrusions
Actuators
Air nozzles
Alignment couplers
Ball joints
Bearings
Inner races
Linear bearings
Locking devices
Radial bearings
Takeup frames
Thrust washers
Brakes/Clutches
Breaker plates
Cam followers
Chain links
Clamps
Connectors
Couplings
Drive tensioners
Encoders
E-Rings
Filter units
Gauges
Gear reducers
Gears
Grease fittings
Grippers
Hand wheels
Hardware (contains several varieties of fasteners)
Hose barbs
Human figures
Hydraulic cylinders
Inserts
Knobs
Latches
Levelling pads
Motors
O-Rings
Panels-electrical
Pipe fittings
Pneumatic cylinders
Pneumatic filters / regulators
Pneumatic fittings
Pneumatic valves
Potentiometers
Rollers
Screws
Seals
Sensors
Shaft collars
Shaft mounts
Shaft supports
Shafting
Sheaves
Shims
Shock absorbers
Slide units
Snap rings
Solenoid valves
Springs
Sprockets
Switches
Thermocouples
Torque limiters / clutches
Vacuum pumps
Water rotary joints

Come and get it, but don't complain when they're gone.

 

I'm downloading in the "H's", please keep your parts and assemblies until
later today (tonight).

Thanks for all your support!
Keith

PS what do I need to remove to reply direct? DOT, UNDERLINE and/or again?

 

Remove anything capitalized. Replace UNDERLINE with (guess) . . . an
underline.