out of memory? don't think so!

Discussion in 'SolidWorks' started by Walms, Nov 14, 2003.

  1. Walms

    Walms Guest

    Hi Folks,
    I have an assembly with about 10000 parts, with 1000 of them unique.
    As a rule I don't work on the assembly with all parts unsuppressed but I've
    been asked to
    forward the complete assembly as an edrawing for a dog and pony show.

    When I try to save as edrawing in both 2003 sp4 and 2004 sp0 the computer
    works away for about 15 minutes and then craps out! Unhandled error !!!
    Other attempt I get a message stating insufficient memory. The memory usage
    hovers around 1.2gigs.
    My system has 2 gigs of ram and a 2 gigs allocated for a swap file.

    I've wasted a day on this fricken problem and the brass is getting
    impatient.
    Anyone? Please!
     
    Walms, Nov 14, 2003
    #1
  2. Try saving with edrawing data it is an option in the saveas.
    You could also check it in Tools>Options>Save eDrawing data in SolidWorks
    Document

    Corey
     
    Corey Scheich, Nov 14, 2003
    #2
  3. Walms

    Todd Guest

    What Corey said...then:

    After you save the assembly in SolidWorks with that option enabled, then
    open the assembly from E-Drawings directly.

    You should be able to save from that...

    --Todd
     
    Todd, Nov 14, 2003
    #3
  4. I guess I left it a little open ended didn't I thanks for the Tag-Team

    Corey
     
    Corey Scheich, Nov 14, 2003
    #4
  5. Walms

    Walms Guest

    Excellent! It worked.
    Now my next problem... The edrawing file size is 16 mb. I tried to load it
    on the generic computer used for the presentation, it can't handle the
    large file.
    What would my next option be? Make an AVI file?
     
    Walms, Nov 14, 2003
    #5
  6. Walms

    matt Guest

    You're gonna think I'm nuts, but try to set your virtual memory to 500 Mb
    or so. Tell us what happens.

    matt
     
    matt, Nov 14, 2003
    #6
  7. When you open it in eDrawing save as easm and select at the bottom to
    compress that is as small as eDrawings will go The graphics on it will be a
    little dumbed down but should be alright.
     
    Corey Scheich, Nov 14, 2003
    #7
  8. Walms

    Arlin Guest

    You could just try the plain old SWX Viewer. This is less demanding on
    hardware than edrawings.
     
    Arlin, Nov 14, 2003
    #8
  9. Walms

    Jeff N Guest

    Walms,
    Do you have 3D Instant Website as an add-in? If so, you may want to try that
    route.
     
    Jeff N, Nov 17, 2003
    #9
  10. save the assembly as a part with only external surfaces. then make a
    e-drawing from that.
     
    Sean Phillips, Nov 17, 2003
    #10
  11. I know how to save an assy as a part, but how do I tell it to only keep
    external surfaces?

    WT
     
    Wayne Tiffany, Nov 17, 2003
    #11
  12. it is an option at the bottom of the saveas window.

    o exterior faces
    o exterior parts
    o all components


    corey
     
    Corey Scheich, Nov 17, 2003
    #12
  13. Sorry, egg on face. Forgot to switch the type to .prt before observation.
    I hang my head in shame.... :)))

    WT
     
    Wayne Tiffany, Nov 17, 2003
    #13
  14. Walms

    matt Guest

    I'll bet you're going to run into this problem again. You just got a
    temporary work around. I think the real problem is the Windows memory
    limitation. Windows can only handle so much memory between RAM and VM. If
    you have 2 Gb RAM, I would back off the VM to get the total under 3 Gb. If
    you do a search in this NG for memory limitation, you'll probably be able
    to find the details.
     
    matt, Nov 17, 2003
    #14
  15. Walms

    Your Momma Guest

    MoldWorks/SplitWorks add on software. Otherwise you need to construct
    EVERY mold component manualy just as you did initialy in your 2d
    software before your library was built up.
     
    Your Momma, Feb 5, 2004
    #15
Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.